ScanPal®2Portable Data TerminalUser manualPrinted August 2001
4. Software organizationThe ScanPall2 software system consists of three modules:• The Kernel module• The System (Operating System) module• The Pro
For further information, refer to section 5.3.
Program ModuleThe Program module operates on top of the System module. The user programsare downloaded into this module.The user program, downloaded
For further information on the development tools, contact one of the Metrologicoffices:Metrologic Instruments, Inc – Corporate HeadquartersTel: 856-22
5. OperationsBefore any operation, it is advisable to make sure that the replaceable batteries are new,or that the rechargeable battery is correctly
FunctionThis key cannot be used on its own, but in combination with anumeric key (1 to 9), in order to obtain a specific function,depending on the pr
Program ModeThis is the default operating mode when the ScanPall2 is powered up. It dependson the user program loaded into the Program module.The a
2. Upload dataUploads the data collected, via the selected upload port.The letter displayed on the screen, at the right of the Upload Data line,indic
- Data DeletionDefines whether, after an upload, the data is deleted Manually, witha request for confirmation, or Automatically, with no request forc
ScanPal 2The content of this manual is the property of Metrologic Instruments Inc. The information contained inthis manual has been carefully checked
Defines the date and time.
• Download ProgramDownloads an application (*.ATX) created with the application generatorinto the ScanPall2 Portable Terminal, via the selected downl
System ModeTurn off the ScanPall2, and then simultaneously press the ,and keys to enter System mode.System mode offers the foll
• SpeedDefines the CPU operating speed. Five speeds are available:Speed ConsumptionFull... 39 mA1/2...22
3. ReaderTests the scanner read performance and displays the bar code read, itslength, and a letter identifying the code type (symbology).The symbolog
Tests the LCD screen and the dual-colour LED.Press the key to start or stop the test.
• KBDTests the keypad keys.Pressing a key displays its value on the screen. The function keymust be used in combination with a numeric key
Kernel ModeTurn off the ScanPall2, and then simultaneously press the ,and keys to enter System mode; next turn off the ScanPa
4. VersionDisplays the following information:Hardware version number ...(H/W)Serial number...
OverviewFile Ý.SHXCompiled "C" programFile KSP2Ý.SHXKernel"C" compiler(3) OORRDownLoad.EXEorIrLoad.EXEDownLoad.EXEorIrLoad.EX
Table of Contents1. Introduction ... 22. Genera
6. Troubleshooting guide• The ScanPall2 doesn’t come on after the key has been pressed.Change the batteries or recharge the battery.• The
If the problem persists, contact Technical Support.
The scanner doesn’t work.Check that the symbologies of the codes read are enabled.Check whether the battery icon, indicating the charge state, is empt
7. Metrologic references and descriptionsPart Number DescriptionSCANPAL2CBBasic ScanPal 2 CCD kit, including:- 1 ScanPal 2 CCD portable terminal
1. IntroductionThe ScanPall2 is a high performance, light-weight and compact portable terminal,designed for daily intensive use.It is powered by two
2. General characteristicsThe basic characteristics of the ScanPall2 are as follows: Electrical characteristics• Main battery...
• Dual clock with low-speed mode capability for saving the batteries (for furtherinformation on the Speed setting, refer to section 5.3)
Memory• Program... 1-MB Flash-ROM, flash memory used forsaving the program, character sets,constants, etc.• Dat
Indicator• Buzzer .... audible indicator, programmable from 1 KHzto 4 KHz, low-power transducer type• LED ...
For the references and descriptions, refer to section 7.3. Hardware configuration Front, back and side view RS232 and IrDA connectionABCFE D 47 815
Comments to this Manuals