Honeywell T7300D User Manual download pdf (Page 13)

T7200D,E, T7300D,E,F AND Q7300 SERIES 2000 PROGRAMMABLE COMMERCIAL THERMOSTATS AND SUBBASES

13 63-4355—4

IMPORTANT

Review the settings to confirm that they match the

system. Press Run Program to exit the Installer

Setup. The thermostat has saved the Installer Setup

changes and initiated reset in order to operate with

these new settings. Be sure to set the current day

and time immediately.

Setting Current Time/Day

Press Set Current Day/Time.

NOTE: On initial power up or after an extended power

loss, 1:00 pm flashes on the display until a key

is pressed.

Press Day until the current day is displayed.

NOTE: Sun = Sunday, Mon = Monday, Tue = Tuesday,

Wed = Wednesday, Thu = Thursday,

Fri = Friday, Sat = Saturday.

Press increase

▲

or decrease

▼

key until the current

time is displayed.

NOTE: Tapping Set Current Day/Time changes the

time in one hour increments.

Press Run Program.

INSTALLER SYSTEM TEST

Use the Installer System Test to check the thermostat

configurations and operation. Refer to Table 8 for a list of

available system tests. To start the system test:

CAUTION

Possible Equipment Damage.

Equipment damage can result if compressor is

cycled too quickly.

The minimum off time for compressors is bypassed

during the Installer System Test. Equipment damage

can occur if the compressor is cycled too quickly.

Press and hold both the increase

▲

and

decrease

▼

keys

until

appears. All segments of the LCD display for three

seconds before

appears. See Fig. 15 and 16.

Temperature

display adjustment.

37 0 No difference in displayed

temperature and actual room

temperature.

1 - 6 1: Display adjusts to 1°F (0.6°C) higher

than actual room temperature.

2: Display adjusts to 2°F (1.1°C) higher

than actual room temperature.

3: Display adjusts to 3°F (1.7°C) higher

than actual room temperature.

4: Display adjusts to 1°F (0.6°C) lower than

actual room temperature.

5: Display adjusts to 2°F (1.1°C) lower than

actual room temperature.

6: Display adjusts to 3°F (1.7°C) lower than

actual room temperature.

Minimum off-time

in heating.

38 4 4: 4-minute minimum off-time 0, 1, 2,

3, or 5

Minimum number of minutes (0 through 5)

the heating equipment is off between calls

for heat.

Not used. 39 — — — — —

Installer Setup

lockout (enable/

disable keypad

lockout using DIP

switch 1 on

thermostat back).

40 0 0: No Installer Setup lockout. 1 1: Installer Setup lockout activated.

Table 7. Thermostat Installer Setup Options. (Continued)

Select

Installer Setup

Number

(Press Unoccupied

Temp to change)

Factory Setting

Other Choices

(Press

▲

▼

to change)

Actual

SettingDisplay Description Display Description

Number 2 must be set to 1 to extend fan operation.

Number 22 must be set to 1 and remote sensor(s) must be installed.

M4951B

Set Current

Day/Time

Set Program Set Temperature Change

Time/Temp

Occupied

Temp

Unoccupied

Start Time Day

System Fan

Copy

Occupied

Start Time

Run

Program

Temporary

Occupied

Continous

Unoccupied

Set Current

Day/Time

Clear

Start Time

Unoccupied

Temp

Heat/Cool

Settings

Mon

Set Day/Time

M4952B

Set Program Set Temperature Change

Time/Temp

Occupied

Temp

Unoccupied

Start Time Day

System Fan

Copy

Occupied

Start Time

Run

Program

Temporary

Occupied

Continous

Unoccupied

Set Current

Day/Time

Clear

Start Time

Unoccupied

Temp

Heat/Cool

Settings

Day

Tue

Set Day/Time

M4953B

Set Program Set Temperature Change

Time/Temp

Occupied

Temp

Unoccupied

Start Time Day

System Fan

Copy

Occupied

Start Time

Run

Program

Temporary

Occupied

Continous

Unoccupied

Set Current

Day/Time

Clear

Start Time

Unoccupied

Temp

Heat/Cool

Settings

Tue

Set Day/Time

M4954A

Set Program Set Temperature Change

Time/Temp

Occupied

Temp

Unoccupied

Start Time Day

System Fan

Copy

Occupied

Start Time

Run

Program

Temporary

Occupied

Continous

Unoccupied

Set Current

Day/Time

Clear

Start Time

Unoccupied

Temp

Heat/Cool

Settings

Auto

System Fan

Mon

Room

Occupied 1

Heat

Run

Program

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 35 36

Comments to this Manuals

No comments

Honeywell T7300D User Manual Page 13

Comments to this Manuals

Related products and manuals for Thermostats Honeywell T7300D