Honeywell H1008Automatic Humidity ControlwithHumidiCalc+ SoftwareCopyright © 1998 Honeywell Inc. • All Rights ReservedRev 1.0May 27, 1998
Rev 2.063-7048 1998 Honeywell Inc.Page 10 of 22adjusting a single input value, we can achieve a control point that satisfied every one ofthe thousand
Rev 2.063-7048 1998 Honeywell Inc.Page 11 of 22Nobody has more knowledge about heating loads than Honeywell, the world leader intemperature control.
Rev 2.063-7048 1998 Honeywell Inc.Page 12 of 22-20-10010203040506070800 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 320510152025303540Furnace CyclesHumi
Rev 2.063-7048 1998 Honeywell Inc.Page 13 of 22-20-10010203040506070800 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 320510152025303540Furnace CyclesHumi
Rev 2.063-7048 1998 Honeywell Inc.Page 14 of 22-20-100102030405060708000:00:0001:00:0002:00:0003:00:0004:00:0005:00:0006:00:0007:00:00.008:00:0009:00
Rev 2.063-7048 1998 Honeywell Inc.Page 15 of 22 Making the Best of a Duct Mounted Humidity ControlOne of the things we learned early on in this deve
Rev 2.063-7048 1998 Honeywell Inc.Page 16 of 22 -20-10010203040506070809010008:00:0008:30:00.009:00:0009:30:0010:00:0010:30:0011:00:0011:30:0012:00:0
Rev 2.063-7048 1998 Honeywell Inc.Page 17 of 22 2. Humidity Control Located Too Close to Bypass DuctA second problem that can occur in many installat
Rev 2.063-7048 1998 Honeywell Inc.Page 18 of 22dewpoint increases slightly in response to the humidifier cycles. During thisperiod the relative humi
Rev 2.063-7048 1998 Honeywell Inc.Page 19 of 22While the humidifier was on during the entire recovery period starting at 4:15a.m., the sensed RH rang
Rev 2.063-7048 1998 Honeywell Inc.Page 2 of 22 Automatic Humidity ControlThe Honeywell H1008 Automatic Humidity Control with HumidiCalc+ Softwareis
Rev 2.063-7048 1998 Honeywell Inc.Page 20 of 22a ¾” diameter hole to be cut in the duct. Drilling this hole with a uni-bit is asnap. Simply drill t
Rev 2.063-7048 1998 Honeywell Inc.Page 21 of 22Logic to determine if the fan is running is determined from the equipment inputsso a current sensing r
Rev 2.063-7048 1998 Honeywell Inc.Page 22 of 22 Direct Comparison Chart – Honeywell H1008 Automatic Humidity Control with HumidiCalc+ Software vs.
2XXXXXXXXXXXX-XXXXHoneywell Europe S.A.3 Avenue du Bourget1140 BrusselsBelgiumHoneywell Asia Pacific Inc.Room 3213-3225Sun Hung Kai CentreNo. 30 Harbo
Rev 2.063-7048 1998 Honeywell Inc.Page 3 of 22 Defining a Comfortable Humidity Level Much research has been conducted on what combination of tempera
Rev 2.063-7048 1998 Honeywell Inc.Page 4 of 22 The message to take away from all this is: If you are in the business of trying to provide a comfort
Rev 2.063-7048 1998 Honeywell Inc.Page 5 of 22Figure 3 illustrates why condensation occurs:Figure 3 – Temperature Profile of Double Pane WindowFigure
Rev 2.063-7048 1998 Honeywell Inc.Page 6 of 22 Outdoor Temperature Compensating Humidity ControlsHoneywell, with the Perfect Climate Comfort Center
Rev 2.063-7048 1998 Honeywell Inc.Page 7 of 22The AutoTrac control does not have the ability to provide true dewpoint control. Thismay result in ov
Rev 2.063-7048 1998 Honeywell Inc.Page 8 of 22 H1008 Automatic Humidity Control with HumidiCalc+ - The TechnicalApproachWe found that there is more
Rev 2.063-7048 1998 Honeywell Inc.Page 9 of 22oversize). In this case the furnace will only be running 50% of the time at the ASHRAEdesign temperatu
Comments to this Manuals