Honeywell MS5145 Eclipse User's Guide

METROLOGIC INSTRUMENTS, INC. MS5100 Eclipse™ Series Installation and User’s Guide

6 Figure 5.INTRODUCTION Cable Removal Disconnect the power supply from the PowerLink cable and turn off power to the host system before removing t

7INSTALLATION RS232, Light Pen or Laser Emulation 1. Turn off the host system. 2. Plug the male, 10-pin RJ45 end of the PowerLink cable into t

8 INSTALLATION RS485S 1. Turn off the host system. 2. Plug the male 10-pin RJ45 end of the MVC cable into the 10-pin socket on the MS5145. 3. C

9INSTALLATION Keyboard Wedge 1. Turn off the host system. 2. Plug the male, 10-pin RJ45 end of the PowerLink cable into the 10-pin socket on

10 INSTALLATION Stand-Alone Keyboard 1. Turn off the host system. 2. Connect the 10-pin RJ45 male connector into the jack on the Eclipse. Ther

11Figure 10. USBINSTALLATION USB: Low Speed USB (-38) Full Speed USB (-40) 1. Turn off the host system. 2. Connect the 10-pin RJ45 male connec

12 SCANNER OPERATION How to Use CodeGate and the Manual Activation Mode CODEGATE® MANUAL ACTIVATION MODE* * This feature is not a default setti

13SCANNER OPERATION Indicators Audible When the MS5145 scanner is operational, the scanner provides audible feedback to indicate the status o

14 SCANNER OPERATION Indicators Visual The MS5145 is equipped with a red LED and green LED which indicate the scanner’s state and the status o

15SCANNER OPERATION Indicators Failure One Razzberry Tone – On Power Up This indicates the scanner has experienced a laser or flipper subsyste

Copyright © 2008 by Metrologic Instruments, Inc. All rights reserved. No part of this work may be reproduced, transmitted,

16 SCANNER OPERATION Depth of Field vs. Minimum Bar Code Element Width Minimum Bar Code Element Width A B C D E F mm .10 .12 .17 .26 .33

17SCANNER OPERATION Configuration Modes The MS5145 Eclipse has three modes of configuration. • Bar Codes The Eclipse can be configured by sca

18 SCANNER OPERATION 4. During configuration, the motor and laser turn off. YOU CANNOT SCAN A BAR CODE WHILE IN SERIAL CONFIGURATION MODE. 5. T

19SCANNER OPERATION EXAMPLE #3: The following example shows the events that occur when an invalid bar code is sent. This sample will load the f

20 TROUBLESHOOTING GUIDE The following guide is for reference purposes only. Contact a Metrologic representative at 1-800-ID-Metro or 1-800-436-3

21TROUBLESHOOTING GUIDE Symptoms Possible Causes Solution The unit powers up, but does not scan and/or beep. The unit is trying to scan a partic

22 TROUBLESHOOTING GUIDE Symptoms Possible Causes Solution The unit scans but the data is not correct. The unit’s configuration is not correct. M

23RS232 DEMONSTRATION PROGRAM If an RS232 scanner is not communicating with your IBM compatible PC, key in the following BASIC program to test tha

24 DESIGN SPECIFICATIONS MS5145 Eclipse OPERATIONAL Light Source: Visible Laser Diode (VLD) @ 650 nm Laser Power: Less than 1.0 mW average Depth

25DESIGN SPECIFICATIONS MS5145 Eclipse ELECTRICAL Input Voltage: 5VDC ± 0.25V Power: Operating 675 mW Current: Operating 135 mA average @ 5V

iiTABLE OF CONTENTS Introduction... 1 Scan

26 APPLICATIONS AND PROTOCOLS The model number on each scanner includes the scanner number and factory default communications protocol. Scanner

27DEFAULT SETTINGS Many functions of the scanner can be configured or enabled/disabled. The scanner is shipped from the factory configured to a

28 DEFAULT SETTINGS Parameter Default RS232Light Pen RS485SKBW USBLaser EmulationITF Symbol Lengths Variable       Minimum Symbol L

29DEFAULT SETTINGS Parameter Default RS232Light Pen RS485SKBW USBLaser EmulationInfinite Same Symbol Timeout       Inter-Character

30 DEFAULT SETTINGS Parameter Default RS232Light Pen RS485SKBW USBLaser EmulationTransmit Sanyo ID Characters   Nixdorf ID   L

31DEFAULT SETTINGS Parameter Default RS232Light Pen RS485SKBW USBLaser Emulation100 msec to Find Supplement Configurable in 100 msec Steps (m

32 UPGRADING THE FLASH ROM FIRMWARE The MS5145 is part of Metrologic's line of scanners with flash upgradeable firmware. The upgrade process

33SCANNER AND CABLE TERMINATIONS Scanner Pinout Connections The MS5145 scanner interfaces terminate to a 10-pin modular jack. The serial number

34 SCANNER AND CABLE TERMINATIONS Figure 16. MS5145-00 Laser Emulation Pin Function 1 Ground 2 RS232 Transmit Output 3 RS232 Receive Input 4

35SCANNER AND CABLE TERMINATIONS Cable Connector Configurations RS232 PowerLink Cable, 55-55000x-3 Pin Function 1 Shield Ground 2 RS232 Tran

iii TABLE OF CONTENTS Regulatory Compliance Safety ...

36 SCANNER AND CABLE TERMINATIONS Cable Connector Configuration Keyboard Wedge PowerLink Cable 55-55002A-3 Pin Function 1 Keyboard Clock 2 Key

37REGULATORY COMPLIANCE Safety ITE Equipment IEC 60950-1, EN 60950-1 Laser Laser Class 1: IEC 60825-1:1993+A1+A2, EN 60825-1:1994+A1+A2 Cau

38 REGULATORY COMPLIANCE EMC Emissions FCC Part 15, ICES-003, CISPR 22, EN 55022 Immunity CISPR 24, EN 55024 NOTE: Immunity performance is not

39REGULATORY COMPLIANCE EMC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s autho

40 LIMITED WARRANTY The MS5145 Eclipse™ scanners are manufactured by Metrologic at its Suzhou, China facility. The MS5145 Eclipse scanners have a

41PATENTS This METROLOGIC product may be covered by, but is not limited to, one or more of the following U.S. Patents: U.S. Patent No.; 5,216,2

42 INDEX A AC ... see power accessories ...2, 3 aperture...

43INDEX S safety...37, 39 stand ...3 Stand-Alone Keyboard see interf

44

1INTRODUCTION The MS5145 Eclipse™ is a single-line, hand-held laser scanner. Equipped with Metrologic’s patented CodeGate® technology, Eclipse

August 2008 70-79016D

2 INTRODUCTION Scanner and Accessories BASIC KIT Part # Description MS5145 Eclipse Scanner 00-02544x MetroSelect Single-Line Configuration Guid

3INTRODUCTION Scanner and Accessories OPTIONAL ACCESSORIES Part # Description 55-55000x-3 RS232 PowerLink Cable with Built in Power Jack straig

4 INTRODUCTION Scanner Components ITEM NO. DESCRIPTION 1 Mode Select Button/CodeGate Button (see page 12) 2 Red LED (see page 14) 3 Green LED

5INTRODUCTION Caution and Serial Number Labels Figure 2. Label Location on the Bottom of the Scanner with Example Caution To maintain compl