900.0570 – September 2005 – Rev. 1.01HJZTP/HJZTPXJoystick Controller forPTZ Cameras, DVRs, and MultiplexersUser Manual
Rev. 1.01 x 900.05708-Sept-05TABLE OF CONTENTS, CONTINUED8.3 CONTROLLING SCAN ASSEMBLIES...
Rev. 1.01 1 900.05708-Sept-05SECTION 1:INTRODUCTION1.1 PRODUCT DESCRIPTIONThe HJZTP Keyboard can control DVRs, multiplexers, and PTZs using Honeywell
Rev. 1.01 2 900.05708-Sept-051.3 PACKAGE CONTENTSQuantity Description1 HJZTP or HJZTPX Joystick Controller1 HJZMU001150 User Manual1 120 VAC to 12VDC
Rev. 1.01 3 900.05708-Sept-05SECTION 2:INSTALLATION2.1 CONNECTIONSAll connections to and from the keyboard are made to the RJ type connectors locatedo
Rev. 1.01 4 900.05708-Sept-052.2 SUPPLIED CABLES2.2.1 Eight-Way RJ45 Connector to Eight-Way RJ45 ConnectorThis cable is used to connect a slave keyboa
Rev. 1.01 5 900.05708-Sept-052.3 DOME CONNECTIONS2.3.1 Daisy chainFigure 4. DOME DAISY CHAIN CONFIGURATION
Rev. 1.01 6 900.05708-Sept-052.3 DOME CONNECTIONS, CONTINUED2.3.2 Star Wiring ConfigurationNote: Details on termination and dome installation are cove
Rev. 1.01 7 900.05708-Sept-052.4 DVR AND MULTIPLEXER CONNECTION2.4.1 DVR SetupThe DVR unit ID and RS485 port settings must be correctly set using the
Rev. 1.01 8 900.05708-Sept-052.5 KEYBOARD CASCADINGIt is possible to cascade up to three slave keyboards off a master keyboard that isconnected to the
Rev. 1.01 9 900.05708-Sept-052.6 CONNECTOR PIN ASSIGNMENTSViewed from wiring input side of plugFigure 2. KBD/AUX/CONTROL CONNECTORSKBDPin Signal Usual
Rev. 1.01 ii 900.05708-Sept-05ISSUE DATE REVISIONSHJZMU001150A March 2005 Initial Release.B July 2005 Revised Model # (ECI 2003)900.05701.00 August 20
Rev. 1.01 10 900.05708-Sept-052.6 CONNECTOR PIN ASSIGNMENTS, CONTINUEDViewed from wiring input side of plugFigure 3. POWER CONNECTORPOWERPin Signal Us
Rev. 1.01 11 900.05708-Sept-05SECTION 3:SETUP3.1 KEYBOARD LOCKIf the keyboard is locked, the ‘lock’ key will be illuminated, and the LCD display willd
Rev. 1.01 12 900.05708-Sept-053.2 LCD DISPLAYThe LCD display shows information about the current operating state of the keyboard. Ifthe keyboard is op
Rev. 1.01 13 900.05708-Sept-053.3 SYSTEM SETUPBefore using the HJZTP keyboard it must be set-up to meet the systems requirements.There are three aspec
Rev. 1.01 14 900.05708-Sept-053.3.2 DVR/Multiplexer/Camera ConnectionNote: The DVR/multiplexer/camera connection can only be set from the masterkeyboa
Rev. 1.01 15 900.05708-Sept-053.3.2 DVR/Multiplexer/Camera Connection, ContinuedExample: If a system has 40 cameras with:DVR 1, a 4-way DVR connected
Rev. 1.01 16 900.05708-Sept-053.3.3 Dome (PTZ) ProtocolThe keyboard can be set up to control RapidDome/Orbiter type domes using HoneywellVCL protocol
Rev. 1.01 17 900.05708-Sept-05SECTION 4:DVR CONTROL FUNCTIONS4.1 DVR MODEPress the ‘mode’ key to toggle between multiplexer and DVR mode.4.2 NUMBER EN
Rev. 1.01 18 900.05708-Sept-054.4 PICTURE CONTROLThe following table indicates the keys used for picture control:Key Functiondisplay Displaysequence S
Rev. 1.01 19 900.05708-Sept-054.7 RECORDING AND PLAYBACKThe following table indicates the keys used for recording and playback, only the counterfuncti
Rev. 1.01 iii 900.05708-Sept-05FCC COMPLIANCE STATEMENTInformation to the User: This equipment has been tested and found to comply with thelimits for
Rev. 1.01 20 900.05708-Sept-054.8 ALARM FUNCTIONIf an alarm is active, press the ‘alarm’ key to reset the DVR’s outputs (including internalbuzzer).If
Rev. 1.01 21 900.05708-Sept-05SECTION 5:MULTIPLEXER CONTROL FUNCTIONS5.1 MULTIPLEXER MODEPress the ‘mode’ key to toggle between multiplexer and DVR mo
Rev. 1.01 22 900.05708-Sept-055.2.2 Bottom MenuTo enter the multiplexer bottom menu press the ’F2’ (‘▼’), key twice to display:Full 2x2 3x3 4x4 PIPUse
Rev. 1.01 23 900.05708-Sept-055.3 PICTURE CONTROL, CONTINUEDPress the ‘play’ key to select the VCR input for display. (Pressing the key again willretu
Rev. 1.01 24 900.05708-Sept-055.6 MULTIPLEXER SELECTIONPressing a number followed by the ‘Fn’ key selects a multiplexer to control. This alsoselects t
Rev. 1.01 25 900.05708-Sept-05SECTION 6:PTZ CONTROL FUNCTIONS WHEN USING HONEYWELL VCL(RAPIDDOME/ORBITER DOME) PROTOCOL6.1 PTZ CAMERA SELECTION CONTRO
Rev. 1.01 26 900.05708-Sept-05HONEYWELL VCL PROTOCOL, CONTINUED6.5 ZOOMRotate the top of the joystick clockwise to zoom in.Rotate the top of the joyst
Rev. 1.01 27 900.05708-Sept-05HONEYWELL VCL PROTOCOL, CONTINUED6.8 MANUAL CHANGE OVER (CHANGE OVER RAPIDDOME/ORBITER DOMESONLY)The operator can force
Rev. 1.01 28 900.05708-Sept-05HONEYWELL VCL PROTOCOL, CONTINUED6.9.3 To Start a Tour of PresetsA RapidDome/Orbiter can store four different preset tou
Rev. 1.01 29 900.05708-Sept-05HONEYWELL VCL PROTOCOL, CONTINUED6.9.5 To Vary the Standard Speed of a Tour, Continued7. Press ‘2’, then press the ‘180°
Rev. 1.01 iv 900.05708-Sept-05IMPORTANT SAFEGUARDS1. READ INSTRUCTIONS – All safety and operating instructions should be read before the unit isoperat
Rev. 1.01 30 900.05708-Sept-05HONEYWELL VCL PROTOCOL, CONTINUED6.9.7 To Vary the Standard Speeds and Dwell Times of a Tour, ContinuedThe tour is now s
Rev. 1.01 31 900.05708-Sept-05HONEYWELL VCL PROTOCOL, CONTINUED6.10.1 HomeSelect ‘HOME’ in the camera setup menu, then press ‘aux’ to display the home
Rev. 1.01 32 900.05708-Sept-05HONEYWELL VCL PROTOCOL, CONTINUED6.10.3 Remote ResetSelect ‘RESET’ in the camera setup menu, then press ‘aux’ to display
Rev. 1.01 33 900.05708-Sept-05HONEYWELL VCL PROTOCOL, CONTINUED6.10.5 IR LampsSelect ‘IR/LAMP’ in the camera setup menu, then press ‘aux’ to display t
Rev. 1.01 34 900.05708-Sept-05Notes:
Rev. 1.01 35 900.05708-Sept-05SECTION 7:PTZ CONTROL FUNCTIONS WHEN USING HONEYWELL DIAMOND(KD6/HD6) PROTOCOL7.1 PTZ CAMERA SELECTION (HONEYWELL DIAMON
Rev. 1.01 36 900.05708-Sept-05HONEYWELL DIAMOND PROTOCOL, CONTINUED7.3 PAN AND TILTPrecise control of pan and tilt can be achieved using the joystick.
Rev. 1.01 37 900.05708-Sept-05HONEYWELL DIAMOND PROTOCOL, CONTINUED7.8 PRESHOT SEEKTo seek preshot 1:1. Press key ‘1’.2. Press the ‘preset’ key.Presho
Rev. 1.01 38 900.05708-Sept-05HONEYWELL DIAMOND PROTOCOL, CONTINUED7.12 NIGHTSHOTPress ‘aux’ or enter preshot 99 to toggle the camera between nightsho
Rev. 1.01 39 900.05708-Sept-05HONEYWELL DIAMOND PROTOCOL, CONTINUED7.15 ON SCREEN DISPLAY (OSD) MENUS, CONTINUEDSelecting ‘GOTO’ will display the dome
Rev. 1.01 v 900.05708-Sept-05IMPORTANT SAFEGUARDS14. DAMAGE REQUIRING SERVICE – Unplug the unit from the outlet and refer servicing to qualifiedservic
Rev. 1.01 40 900.05708-Sept-05HONEYWELL DIAMOND PROTOCOL, CONTINUED7.15 ON SCREEN DISPLAY (OSD) MENUS, CONTINUEDFor ‘setup’, ‘preshot program’, ‘vecto
Rev. 1.01 41 900.05708-Sept-05SECTION 8:PTZ CONTROL FUNCTIONS WHEN USING HONEYWELL MAXPROMODE (KD6/HD6) PROTOCOL8.1 INTRODUCTIONThis section provides
Rev. 1.01 42 900.05708-Sept-058.6 PRESHOTSWhen using Maxpro mode, there are several PreShots (views or presets) reserved forcontrolling and programmin
Rev. 1.01 43 900.05708-Sept-058.7 VECTORSCANS (VIDEO TOUR)CAUTION: Continuous VectorScan operation forextended periods of time (> 8 hours) is notre
Rev. 1.01 44 900.05708-Sept-058.10 PROGRAMMING PTZ TOURSPreShots 83, 84, and 85 have been reserved for programming PTZ tours 1, 2, and 3.1. Enter a Pr
Rev. 1.01 45 900.05708-Sept-05SECTION 9:TECHNICAL SPECIFICATIONSFeatures HJZTP / HJZTPXMax dome control 128Max DVR control 8 x 16 way, 14 x 9 way, 32
Rev. 1.01 46 900.05708-Sept-05Notes:
Rev. 1.01 47 900.05708-Sept-05APPENDIX A:MENU NAVIGATIONMAIN SCREENDOMEFUNCTIONSHOME TIMEMIMIC RECORDINGCAMERA / DVR/MUX ASSIGNMENTLOCKLOCKLOCKLOCKLOC
Rev. 1.01 48 900.05708-Sept-05Notes:
Rev. 1.01 49 900.05708-Sept-05APPENDIX B:DIAGNOSTICSB.1 JOYSTICK AUTO CALIBRATIONPressing and holding the ‘lock’ key and pressing ‘F1’ (‘▲’) will cali
Rev. 1.01 vi 900.05708-Sept-05Prior to installation and use of this product, please observe the following cautions andwarnings.CAUTIONCAUTION: TO REDU
Rev. 1.01 50 900.05708-Sept-05Notes:
Rev. 1.01 51 900.05708-Sept-05APPENDIX C:VCL (ORBITER/RAPIDDOME) DATA INPUTThe following Honeywell VCL (Orbiter/RapidDome) commands can be input into
Rev. 1.01 52 900.05708-Sept-05Notes:
Rev. 1.01 53 900.05708-Sept-05APPENDIX D:PASSWORDSThe are two user passwords and a keyboard setup code:User level 1 9078User level 2 3434Keyboard Setu
Honeywell Video Systems (Head Office)2700 Blankenbaker Pkwy, Suite 150Louisville, KY 40299www.honeywellvideo.comTEL+1-800-796–2288Honeywell Security A
Rev. 1.01 vii 900.05708-Sept-05TABLE OF CONTENTSSECTION 1: INTRODUCTION ...
Rev. 1.01 viii 900.05708-Sept-05TABLE OF CONTENTS, CONTINUED4.6 DVR SELECTION ......
Rev. 1.01 ix 900.05708-Sept-05TABLE OF CONTENTS, CONTINUED6.9.8 To Stop a Tour of Presets................
Comments to this Manuals