Honeywell F300 User Manual download pdf (Page 12)

F300 ELECTRONIC AIR CLEANER

68-0240EF-5 12

Check Air Cleaner Operation

With all components in place, turn on air cleaner switch and

energize system blower. Check following points of operation:

1. The neon light next to the On-Off switch is on. The neon

light shows that the air cleaner is energized and the high

voltage power supply is working correctly. If a W8600F is

part of the installation, also check the wall panel and

make sure the On indicator is lit. The W8600F Fault indi-

cator comes on if there is a problem with the high voltage

power supply.

2. Turn off the system blower. The neon light should go off

after a few seconds.

3. Turn on the system blower. With the air cleaner ener-

gized, push the test button. A snapping sound indicates

that the collector voltage is present on the cell.

4. With a multispeed blower, repeat steps 1 through 3 for

each fan speed.

SERVICE

CAUTION

Sharp Edges.

Can cause personal injury.

Carefully handle the cell(s) or wear protective gloves to

avoid cuts from the sharp metal edges.

Cleaning the Cells and Prefilters

To assure optimum performance from the air cleaner, the cells

and prefilters must be cleaned regularly and the postfilters

replaced regularly—every one to six months. Washing

frequency varies, depending on the number of family

members, pets, activities (such as cooking or woodworking)

and smoking habits. Use the Service Reminder Schedule at

the end of this document to help establish and maintain a

regular cleaning schedule. Keep your Service Reminder

Schedule in a convenient location.

NOTE: Media postfilters should be replaced rather than

cleaned. See Replacing Media Postfilters section.

If the air cleaner has a W8600F Air Cleaner Monitor, the

SERVICE indicator activates to indicate filter and cell

maintenance are due. The time between activation of the

SERVICE indicator is based on air cleaner run time that is

selected by the installer at installation.

If the air cleaner has a W8600A AIRWATCH Indicator, the Air

Cleaner LCD arrow blinks to indicate it is time to service the

cells and prefilters. The time between activations of the Air

Cleaner LCD is based on calendar time that is selected at

installation.

NOTE: To let the heating or air conditioning system operate

normally while the cells are being washed, simply turn

off the air cleaner switch.

IMPORTANT

Vacuum the prefilter or brush or soak it in a tub. Do

not wash the prefilter in the dishwasher or car wash.

Automatic Dishwasher

CAUTION

Burn Hazard.

Can cause personal injury.

Allow cells to cool completely in dishwasher at end of

wash cycle or wear protective gloves to avoid burns.

Hot water can accumulate in the tubes supporting

collector plates; tip cells so tubes drain.

IMPORTANT

• Check the dishwasher owner's manual. Some

manufacturers do not recommend washing electronic cells

in their dishwashers.

• If the dishwasher has upper and lower arms, position the

cells carefully to allow good water circulation.

• Be careful to avoid damaging the cells when placing them in

the dishwasher. Broken ionizer wires or bent collector plates

are not included in the warranty.

• Very dirty cells, especially from tobacco or cooking smoke,

can discolor the plastic parts and the lining of some

dishwashers. This discoloration is not harmful. To minimize

it, wash the cells more frequently or try a different brand of

detergent.

• Do not allow the dishwasher to run through the dry

cycle. This bakes on any contaminants not removed during

the wash cycle and reduces air cleaner efficiency.

1. Put the cells on the lower rack of the dishwasher with the

airflow arrow pointing up. It may be necessary to remove

the upper rack. Do not block water flow to the upper arm.

NOTE: Lay a few large water glasses between the spikes on

the lower rack and rest the cell(s) on them so the

spikes do not damage the aluminum collector blades.

2. Using regular dishwasher detergent, allow the dish-

washer to run through the complete wash and rinse

cycle. Do not use the dry cycle. To avoid burns, let the

cells cool completely before removing, or wear protective

gloves when removing the cells. Remember that water

may be trapped inside the cells. Tip the cells so the

tubes can drain.

3. Wipe ionizer wires and contact board on the end of the

cell using thumb and forefinger with a small, damp cloth.

4. Inspect the dishwasher. Rerun wash and/or rinse cycle

with the dishwasher empty if there is dirt or residue from

washing the cells. If dirt or residue seems excessive,

wash cells more often or try a different detergent.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 43 44

Comments to this Manuals

No comments

Honeywell F300 User Manual Page 12

Comments to this Manuals

Related products and manuals for Air filters Honeywell F300