Honeywell T775U User Manual Page 37
- Page / 40
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
T775U SERIES 2000 ELECTRONIC STAND-ALONE CONTROLLER
37 62-0255—07
SUMMARY MENU
The Summary menu provides the ability to view the
schedule (E1 and E2 times) for each relay for each day of
the week.
NOTE: Scheduling must be enabled for the Summary
menu to display. Enabling the schedule is
determined in the Setup process for the Output
Options (see page 21).
Fig. 85. Summary Example - Monday Settings.
For each relay, the Summary display indicates the time
and temperature (in parenthesis) for each of the two
scheduled events E1 and E2.
1. Press the MENU button to view the menu.
2. Use the S and T buttons to highlight SUMMARY.
3. Press the X button to display the Summary
settings.
4. Use the X button to scroll forward through each day
of the week (Monday, Tuesday, Wednesday,
Thursday, Friday, Saturday, and Sunday).
5. While viewing a specific day, use the S and T
buttons to cycle through the individual relay
schedules for that day.
When finished, press the HOME button to return to the
home display screen.
If programmed for Reset control, the Summary setpoints
display as “RES” instead of a temperature value. For
example, the display would show:
MONDAY
STAGES
E1: 06:00AM (RES) - indicating Reset
E2: 06:00PM (05) - setback/offset degrees
TROUBLESHOOTING
Power Loss
The date and time settings are retained for 24 hours after
a power outage. After a power loss of more than 24 hours,
the date and time settings may need to be reentered. All
other settings are stored permanently.
Errors and Diagnostics
The controller provides an error message and diagnostic
status as described below.
Error Message
There is a two-character error code that displays in
response to controller software problems:
EE
EEPROM Failure— The values read back from
the EEPROM are not the same as written into the
EEPROM. This error cannot be field repaired. Replace
the device.
Diagnostic Messages
There are two diagnostic messages that can display in
response to sensor problems. The diagnostic codes that
can flash on the display are:
– –
Sensor Open or Shorted — Two dashes display
when a sensor (typically temperature) is open or
shorted. An open circuit is considered anything
greater than 1570 ohms (greater than 300F), shorted
anything less than 770 ohms (less than -73F). Which-
ever stages are operating with this sensor cease to
control (meaning relays go to OFF and proportional
outputs go to zero percent).
This message can also mean that the sensor is pro-
grammed, but not physically connected.
-60°F or 270°F (-51°C or 132°C) Blinking
Temperature Out of Range — The temperature
display blinks when the sensed temperature range is
outside of the display range, below -60°F (-51°C) or
above 270°F (132°C). The displayed value remains at
that displayed limit and control continues. Controller
continues to function unless an open or shorted state
is detected.
Blinking relay status
Relay Minimum Off Time is Active — On the home
screen, each relay’s indicator () blinks while the
relay’s minimum off time is active.
SPECIFICATIONS
Power: 24, 120, or 240 Vac; 50/60 Hz
A separate earth ground is required for any power
source.
Power Consumption:
• 8 VA maximum at 60 Hz
• 10 VA maximum at 50 Hz
Operating & Storage Temperature Ambient Rating:
• -40°F to 125°F (-40°C to 52°C) @ 50 Hz
• -40°F to 140°F (-40°C to 60°C) @ 60 Hz
Relative Humidity: 5% to 95% non-condensing
Relay Contact Output Ratings (N.O. and N.C.):
• 1/2 hp; 9.8 AFL, 58.8 ALR @ 120 Vac
• 1/2 hp; 4.9 AFL, 29.4 ALR @ 240 Vac
• 125 VA pilot duty @ 120/240 Vac
• 10A @ 24 Vac (resistive)
Modulating Outputs:
• 0-10 Vdc; drive a minimum of 2,000 Ohms
• 2-10 Vdc; drive a minimum of 2,000 Ohms
• 4-20 mA; drive a maximum of 600 Ohms
• Electronic Series 90
• Floating
MENU
SUMMARY
MENU
SUMMARY
MONDAY
RELAY 1-2
E1: 06:00AM (72)
E2: 06:00PM (65)
M24629
- T775U Series 2000 Electronic 1
- Stand-Alone Controller 1
- Actuators 2
- BEFORE INSTALLATION 3
- INSTALLATION AND SETUP 3
- MOUNTING 3
- Reset Temperature Control 4
- Sensor Wiring 5
- 62-0255—07 6 6
- Controller Wiring 7
- Controller Wiring Details 8
- WIRING APPLICATION 9
- EXAMPLES 9
- CHECKOUT 10
- INTERFACE OVERVIEW 11
- Home Screen 12
- Accessing the Menus 12
- Using the Menus 12
- PROGRAMMING OVERVIEW 13
- 1. SETUP 13
- Setup Procedure 14
- 1.2.2.1. TYPE (Sensor A only) 15
- 1.2.2.2.3. MIN or MAX VALUE 16
- 1.2.2.5. Exit Sensor A Setup 17
- 1.3. Setting up the Outputs 17
- 1.3.1.2. MIN OUT % 18
- 1.3.1.3. INTEGRAL 18
- 1.3.1.4. DERIVATIVE 19
- 1.3.1.5. SCHEDULE 19
- 1.3.1.6. RESET 20
- 1.3.1.7. Hide 20
- 1.3.2. NBR OF RELAYS 21
- 1.3.3. OPTIONS 21
- 1.3.3.1. USE SCHED 21
- 1.3.3.2. MIN OFF or MIN ON 22
- 1.3.3.5. Exit Options Setup 23
- 1.3.4. Setting up the Relays 23
- 1.3.4.1. SCHEDULE 23
- 1.3.4.2. RESET 24
- 1.3.4.3. RESET RT (run time) 24
- 1.3.4.4. EXIT Relay Setup 24
- 1.4. Exiting Setup 24
- 2. PROGRAMMING OUTPUTS 25
- (MOD AND RELAY) WITH NO 25
- 2.1.3. SETBACK 26
- 2.1.3. SENSOR 26
- 2.1.5. THROTTLING RANGE or 26
- DIFFERENTIAL 26
- 2.1.6. ACTION 27
- 3. PROGRAMMING OUTPUTS 28
- (MOD AND RELAY) WITH 28
- 3.2.2. RESET B1 or OUTSD MIN 29
- 3.2.4. RESET B2 or OUTSD MAX 30
- 3.2.5. THROTTLING RANGE or 30
- 3.2.6. ACTION 31
- (MOD 2 only) 32
- 4. SCHEDULING 33
- 4.2.1. SET TIME 34
- 4.2.2. SET DATE 34
- 35 62-0255—07 35
- 62-0255—07 36 36
- SUMMARY MENU 37
- TROUBLESHOOTING 37
- SPECIFICATIONS 37
- Emissions Compliance 38
- Immunity Compliance 38
- Safety Compliance 38
- FCC Compliance Statement: 38
- T775U SERIES 2000 CONTROLLER 39
- ® U.S. Registered Trademark 40
- Printed in U.S.A 40
Related products and manuals for Conditioners Honeywell T775U
(4 pages)
(8 pages)© 2020, manymanuals.com. All rights reserved. | 0.684 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals