Honeywell XENON 1902 User Manual Page 168
- Page / 312
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
7 - 26
UPC-A Number System
The numeric system digit of a U.P.C. symbol is normally transmitted at the
beginning of the scanned data, but the unit can be programmed so it will
not transmit it.
Default = On.
UPC-A Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC-A data.
Default = Off for both 2 Digit and 5 Digit Addenda.
UPC-A Addenda Required
When
Required
is scanned, the scanner will only read UPC-A bar codes
that have addenda. You must then turn on a 2 or 5 digit addenda listed on
page 7-26.
Default = Not Required.
Off
* On
* 5 Digit Addenda Off
5 Digit Addenda On
* 2 Digit Addenda Off
2 Digit Addenda On
* Not Required
Required
- Xenon™ 1900/1902 1
- Disclaimer 2
- FCC Part 15 Subpart B Class B 3
- UL Statement 3
- Industry Canada ICES-003 4
- Information 4
- South Korea 6
- International 6
- Solids and Water Protection 7
- C-UL Statement 9
- Australia/NZ 10
- LED Safety Statement 11
- Required Safety Labels 13
- CCB01-010BT Base 14
- Table of Contents 15
- Chapter 5 - Data Editing 20
- Chapter 6 - Data Formatting 20
- Chapter 7 - Symbologies 20
- Chapter 8 - Imaging Commands 22
- Chapter 9 - Interface Keys 22
- Chapter 10 - Utilities 23
- Chapter 13 - Maintenance 24
- Appendix A - Reference Charts 24
- Getting Started 25
- Connecting the Device 26
- Connecting with RS485 30
- Reading Techniques 32
- Setting Custom Defaults 33
- Activate Custom Defaults 34
- Remove Custom Defaults 34
- Activate Defaults 34
- Programming the Interface 35
- RS232 Serial Port 36
- RS485 Packet Mode 37
- RS485 Packet Length 37
- USB IBM SurePos 38
- USB PC or Macintosh Keyboard 38
- USB Serial 39
- ACK/NAK Mode 40
- ACK/NAK Mode On 40
- * ACK/NAK Mode Off 40
- Verifone Ruby Settings 40
- Gilbarco Settings 41
- Honeywell Bioptic Settings 41
- NCR Bioptic Settings 42
- Keyboard Country Layout 44
- Keyboard Country (continued) 45
- Keyboard Style 51
- Keyboard Conversion 52
- Control Character Output On 53
- Default = Off 54
- * Automatic Direct Connect 55
- Mode Off 55
- RS232 Baud Rate 56
- Default = 8 57
- Default = None 57
- RS232 Receiver Time-Out 58
- RS232 Handshaking 58
- Default = XON/XOFF Off 59
- RS232 Timeout 59
- * XON/XOFF Off 59
- XON/XOFF On 59
- Scanner-Bioptic Packet Mode 60
- Scanner-Bioptic ACK/NAK Mode 61
- Cordless System Operation 63
- System Conditions 65
- Page Button 66
- About the Battery 66
- Charging Information 67
- Battery Recommendations 67
- Reset Scanner 70
- Scanning While in Base Cradle 70
- Error Indicators 71
- Scanner Report 72
- Scanner Address 73
- Base Address 73
- Charge Only Mode 73
- Linked Modes 74
- * Open Link Mode 75
- (Single Scanner) 75
- Unlink Scanner 75
- Override Locked Scanner 75
- Alarm Sound Type 76
- Flexible Power Management 77
- :*:RESET_.³ 78
- Batch Mode Beep 79
- Batch Mode Storage 79
- Batch Mode Quantity 80
- Entering Quantities 80
- Quantity Codes 81
- Quantity Codes (continued) 82
- Batch Mode Output Order 82
- Delete Last Code 82
- Clear All Codes 82
- Multiple Scanner Operation 83
- Application Work Groups 86
- All Application Work Groups 87
- PDAs/Mobility Systems Devices 89
- Default = Auto Reconnect On 90
- Reconnect to Off 90
- * Auto Reconnect On 90
- Auto Reconnect Off 90
- Maximum Link Attempts 91
- Relink Time-Out 92
- Host Command Acknowledgment 93
- Host ACK On 94
- * Host ACK Off 94
- Command Action 95
- Input/Output Settings 97
- Trigger Click 98
- Beeper Volume – Good Read 99
- Beeper Pitch – Good Read 99
- Beeper Pitch – Error 100
- Beeper Duration – Good Read 100
- LED – Good Read 100
- Default = 1 101
- Manual Trigger Modes 102
- Serial Trigger Mode 103
- Default = 3600 seconds 104
- Presentation Mode 105
- Centering (page 4-17) 106
- In-Stand Sensor Mode 107
- CodeGate 108
- Streaming Presentation 108
- Mobile Phone Read Mode 109
- Image Snap and Ship 110
- Hands Free Time-Out 110
- Reread Delay 110
- User-Specified Reread Delay 111
- Illumination Lights 111
- Aimer Delay 112
- Scanner Time-Out 112
- Aimer Mode 113
- Centering 113
- Bar Code 1 114
- Bar Code 2 114
- Preferred Symbology 115
- High Priority Symbology 116
- Low Priority Symbology 116
- Preferred Symbology Time-out 116
- Output Sequence Overview 117
- Enter Sequence 118
- Discard 118
- Output Sequence Example 119
- Default Sequence 120
- Transmit Partial Sequence 120
- * Discard Partial Sequence 120
- Multiple Symbols 121
- Video Reverse 122
- Working Orientation 123
- Data Editing 125
- Default 125
- Add CR Suffix 127
- All Symbologies 127
- Add Prefix 127
- Clear One Prefix 127
- Clear All Prefixes 127
- Suffix Selections 128
- Function Code Transmit 128
- Intermessage Delays 128
- Intercharacter Delay 129
- Interfunction Delay 130
- Intermessage Delay 130
- Data Formatting 131
- * Default Data Format 131
- Enter Data Format 132
- Clear One Data Format 133
- Clear All Data Formats 133
- Data Format Editor Commands 134
- Terminal ID Table 134
- Insert symbology name 135
- Insert bar code length 135
- Insert key strokes 135
- Move Commands 136
- Search Commands 136
- Search forward for a string 137
- Search backward for a string 137
- Miscellaneous Commands 138
- Data Formatter 139
- Required, Keep Prefix/Suffix 140
- Single Scan-Data Format 1 142
- Single Scan-Data Format 2 142
- Single Scan-Data Format 3 142
- Single Scan-Primary 142
- Data Format 142
- Symbologies 143
- All Symbologies On 144
- All Symbologies Off 144
- Codabar On/Off 145
- Codabar Start/Stop Characters 145
- Codabar Check Character 145
- D5 6 7 8A 146
- Minimum Message Length 147
- Maximum Message Length 147
- Code 39 On/Off 148
- Code 39 Start/Stop Characters 148
- Code 39 Check Character 148
- Code 39 Message Length 149
- Code 39 Append 149
- Default = Off 150
- 32 Pharmaceutical codes 150
- * Full ASCII Off 151
- Full ASCII On 151
- Code 39 Code Page 152
- Default = No Check Digit 153
- NEC 2 of 5 154
- Code 93 Code Page 157
- Code 11 On/Off 161
- Check Digits Required 161
- Code 128 Message Length 163
- Code 128 Append 163
- Code 128 Code Page 164
- Telepen On/Off 166
- Telepen Output 166
- Telepen Message Length 167
- UPC-A On/Off 167
- UPC-A Check Digit 167
- UPC-A Number System 168
- UPC-A Addenda 168
- UPC-A Addenda Required 168
- UPC-A/EAN-13 169
- Coupon GS1 DataBar Output 170
- UPC-E0 Expand 171
- UPC-E0 Addenda Required 171
- UPC-E0 Addenda Separator 171
- UPC-E0 Check Digit 172
- UPC-E0 Number System 172
- UPC-E0 Addenda 172
- EAN/JAN-13 173
- EAN/JAN-13 Addenda 174
- EAN/JAN-13 Addenda Required 174
- EAN/JAN-13 Addenda Separator 175
- ISBN Translate 175
- EAN/JAN-8 176
- EAN/JAN-8 Addenda 177
- EAN/JAN-8 Addenda Required 177
- EAN/JAN-8 Addenda Separator 177
- MSI On/Off 178
- MSI Check Character 178
- MSI Message Length 179
- GS1 DataBar Omnidirectional 180
- GS1 DataBar Limited 180
- Trioptic Code 182
- Codablock A 182
- Maximum Message Length 185
- Minimum Message Length 185
- GS1 Composite Codes 187
- GS1 Emulation 188
- TCIF Linked Code 39 (TLC39) 189
- QR Code Page 190
- Data Matrix Code Page 192
- Low Density Codes On 192
- * Low Density Codes Off 192
- Aztec Code Page 195
- Postal Codes - 2D 197
- Combination 2D Postal Codes: 198
- Planet Code Check Digit 200
- Postnet Check Digit 200
- Postal Codes - Linear 201
- Korea Post 203
- Imaging Commands 205
- (default) 206
- (Default = 7874) 207
- (default) 209
- (default) 216
- Image Size Compatibility 218
- Signature Capture Optimize 218
- IMGBOX Modifiers 219
- Example: IMGBOX245w37h55y 221
- RF Default Imaging Device 223
- Interface Keys 225
- Supported Interface Keys 227
- Utilities 233
- Data Format Settings 234
- Application Plug-Ins (Apps) 235
- EZConfig Introduction 235
- Scan Data 236
- Configure 236
- Serial Programming Commands 239
- Query Commands 240
- Examples of Query Commands 241
- Trigger Commands 242
- Resetting the Custom Defaults 242
- * Indicates default 243
- # Indicates a numeric 243
- Product Specifications 281
- Parameter Specification 282
- Specifications 283
- 10 Pin RJ41 Modular Plug 285
- Standard Cable Pinouts 287
- 10 Pin Modular Plug 288
- Maintenance 289
- Replacing an Interface Cable 291
- Troubleshooting a 292
- Xenon Scanner 292
- Troubleshooting a Base 293
- Customer Support 295
- Online Technical Assistance 296
- Product Service and Repair 296
- Limited Warranty 297
- Reference Charts 299
- Non-Printable Characters 302
- Printable Characters 302
- Extended ASCII Characters 303
- 104 Key U.S. Style Keyboard 306
- Sample Symbols 307
- Car Registration 308
- Zip Code 308
- Tes t Symbol 308
- Package Label 309
- Test Message 309
- Programming Chart 310
- 9680 Old Bailes Road 312
- Fort Mill, SC 29707 312
- Xenon-UG Rev C 312
Related products and manuals for Scanners Honeywell XENON 1902
Scanners Honeywell 3800gPDF User Manual
(156 pages)
(156 pages)
© 2020, manymanuals.com. All rights reserved. | 0.825 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals