Honeywell 301c User Manual Page 62
- Page / 228
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
60 301C User Manual M-510324
Honeywell 7/10
System Programming
Config Menu
The fourth screen in the Config menu allows a definition of a day and a
week to be programmed.
Day and Week definition allows hours (time frames) to be defined for
either Daytime and Working Days respectively.
Note: Remember, the controller uses a 24 hour clock (0:00 to 23:59).
Any time changes (DST) must be made manually or through
BACNet time synchronisation (BACNet module required).
6. Config
Day definition
Week definition
Day definition
-Daytime-
sta: 08:00
end: 17:00
Week definition
-Working Days-
sta: Monday
end: Friday
- Manuel de l’utilisateur 1
- User Manual 1
- Notices and Trademarks 5
- Symbol Definitions 7
- M-510324 10
- 7/10 Honeywell 11
- Installation Instructions 14
- Surface Mount Installation 15
- Wiring Details 16
- 301C User Manual 15 17
- Power Connections 18
- Communication Connections 18
- Relay Output 19
- Jumper Use Instructions 20
- Getting Started 21
- Programming Interface 22
- LED Definitions 23
- System Operation 23
- VA301C Ver. 3.00 24
- 2007-01-17 13:18:18 24
- System Programming 26
- Tx Info Menu 27
- 1. Tx Info 001 28
- 1. Tx Info 121 29
- COM Menu 31
- Scale Menus (1 and 2) 32
- -Display 34
- 301D2 CH4 Ad001 34
- Alarm A, B and C Menus 35
- Servicing and Operating Menus 36
- Change Tx Address 37
- Groups Menu 39
- Creating Groups 40
- Deleting Groups 41
- Event Menu 42
- 301C User Manual 41 43
- 3. Events 001 44
- Target: Ctrl 44
- Relay: #01 44
- -Delays 45
- Before: 99min 45
- After: 01min 45
- -Coverage Period 50
- All week 50
- 3. EVENT 001 51
- -Status : disabled 51
- Enable event 51
- 10% threshold mode 52
- Start Tx logging 52
- Start event logging 52
- 301C User Manual 51 53
- Acquisition Menu 53
- -Configuration 55
- Config to SDcard 55
- SDcard to Config 55
- Parameters 56
- -System Log 57
- SysLog to SDcard 57
- Config Menu 58
- 301C User Manual 57 59
- Set User Password 60
- Slave Port Cnfg 60
- 301C User Manual 59 61
- Day definition 62
- -Daytime 62
- 7. Network 63
- Reset Database 63
- Scan Network 63
- Reset and Scan 63
- Statistics 001 64
- Valid 16 100% 64
- Errors 0 0% 64
- Timeouts 0 0% 64
- Statistics 65
- Calibration 65
- Network Menu 66
- Tests Menu 67
- 8. Tests 68
- Oprt Mode: normal 68
- Test sequence 69
- BUZZER activated 69
- Any key to continue 69
- Esc to quit 69
- Normal Mode 71
- Single Tx Mode 71
- Debug Mode 71
- Simulation Mode 72
- BACnet Menu 73
- Bacnet Menu 74
- -DHCP : disabled 75
- Enable DHCP 75
- . Consult the IT 76
- -Device Name 77
- Wireless Network Menu 79
- Parameters Menu 80
- 301C User Manual 79 81
- Diagnostics Menu 84
- 1. ID 121 (79h) 85
- 3. Product VA301W 85
- New Node Menu 89
- Hibernate Menu 90
- Reset Network Menu 90
- Status Log Menu 91
- Consolidate Route Menu 91
- 301C User Manual 93 95
- Honeywell 7/10 100
- BACnet/IP MODULE 100
- Statement 101
- 301C User Manual 101 103
- Honeywell 103
- 301C User Manual 103 105
- Specifications 107
- Limited Warranty 109
- 301C User Manual 109 111
- Avis et marques de commerce 115
- Définitions des symboles 117
- Introduction 123
- Instructions d’installation 124
- Installation murale 125
- Détails de connexion 126
- Connexions d’alimentation 128
- Connexions de communication 128
- Sortie relais 129
- Instructions pour cavaliers 130
- Démarrage 131
- Interface de programmation 132
- Fonctions du clavier 132
- Definitions des DEL 133
- Operation du système 133
- Programmation du système 134
- 301C Ver. 3.0 135
- Ad: 1 Gr:0 Ev:0 135
- 2006-05-17 13:18:18 135
- Mot de passe 137
- Menu INFO Tx 138
- 1. InfoTx 001 139
- CO2 (IR) 139
- 1. InfoTx 001 142
- Mdbs RTU 8D 1S EP 142
- 9600 bauds 142
- Echelle (1 et 2) 143
- -Detection 144
- Affichage 145
- Alarme A, B et C 146
- 1. INFO Tx 001 147
- -Entretien 147
- 4002h en fonction 147
- Code d’Etat 148
- Effacer Tx courant 148
- Menu groupes 150
- Créer des groupes 151
- Supprimer des groupes 151
- Menu événement 152
- 3. EVENEMENT 001 154
- -Action 154
- Cible: Ctrl 154
- Relais: #01 154
- -Delais 155
- Avant: 99min 155
- Apres: 01min 155
- Conditions 157
- -Periode couverte 160
- Toute la journee 160
- Toute la semaine 160
- -Statut : desactive 161
- Active evenement 161
- 4. Acquisition 162
- Mode seuil 10% 162
- Debuter log Tx 162
- Debuter log even 162
- Debuter et arreter log Tx 163
- Débuter et arrêter log even 164
- 5. Copie 165
- -parametres 165
- InfoTx vers InfoTx 165
- Evene. vers Evene 165
- -Journal Sys 167
- Journal vers SDcard 167
- Menu config 168
- 6. Config 170
- Mot de passe usage 170
- - 2967 170
- Cnfg port esclave 170
- Adresse: 001 171
- 38400 bauds 171
- Mdbs RTU 8D 2S NP 171
- 7. Reseau 174
- Statistiques 174
- Etalonnage 174
- Valide 16 100% 175
- Erreurs 0 0% 175
- Sans rep 0 0% 175
- Etalonnage 176
- Menu Réseau 177
- Etal Zero 178
- Etal plage 246 ppm 178
- Calib 001 : 301D2 178
- Statut : Normal 178
- Menu Tests 179
- Sequence de test 181
- Mode Normal 183
- Mode Tx unique 183
- Mode débogage 183
- Mode Simulation 184
- Menu BACNet 185
- 9. BACNet 186
- 9. BACNet 187
- -DHCP : desactive 187
- Active DHCP 187
- Menu reseau sans-fil 191
- Parametres 192
- Diagnostics 196
- 1. ID : 121 (79h) 197
- 2. 7B7177EFACE0049 197
- 3. Produit VA301W 197
- Nouveau noeud 202
- Menu Hiberner 203
- Menu RAZ reseau 203
- Menu Log Statut 204
- Menu Consolider Acces 204
- MODULE BACNET/IP 207
- Spécifications 207
- Configuration de réseau 207
- Protocole BACnet/IP 207
- Objets BACNet 208
- Manuel d’utilisateur 301C 97 209
- Description du produit : 217
- Garantie limitée 225
Related products and manuals for Measuring, testing & control Honeywell 301c
(40 pages)© 2020, manymanuals.com. All rights reserved. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals