Honeywell Scanner 1900 User Manual Page 171
- Page / 298
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
7 - 35
When Check Character is set to Validate Type 10/11, but Don’t Transmit,
the unit will only read MSI bar codes printed with the specified type check
character(s), but will not transmit the check character(s) with the scanned
data.
MSI Message Length
Scan the bar codes below to change the message length. Refer to
Message Length Description (page 7-2) for additional information. Mini-
mum and Maximum lengths = 4-48. Minimum Default = 4, Maximum
Default = 48.
Validate Type 10 and Transmit
* Validate Type 10, but Don’t
Transmit
Validate 2 Type 10 Characters,
but Don’t Transmit
Validate 2 Type 10 Characters
and Transmit
Validate Type 10 then Type 11
Character, but Don’t Transmit
Validate Type 10 then
Type 11 Character and Transmit
Disable MSI Check Characters
Minimum Message Length
Maximum Message Length
- Xenon™ 1900/1902 1
- Disclaimer 2
- FCC Part 15 Subpart B Class B 3
- UL Statement 3
- Industry Canada ICES-003 4
- Information 4
- Australia/NZ 5
- South Korea 6
- International 6
- C-UL Statement 8
- Solids and Water Protection 10
- Required Safety Labels 11
- CCB01-010BT Base 12
- Table of Contents 13
- Chapter 5 - Data Editing 17
- Chapter 6 - Data Formatting 18
- Chapter 7 - Symbologies 18
- Chapter 8 - Imaging Commands 20
- Chapter 9 - Interface Keys 20
- Chapter 10 - Utilities 20
- Chapter 13 - Maintenance 21
- Appendix A - Reference Charts 22
- Getting Started 23
- Connecting the Device 24
- Connecting with RS485 28
- Reading Techniques 30
- Save Custom Defaults 31
- Set Custom Defaults 31
- Remove Custom Defaults 32
- Activate Defaults 32
- CR suffix 33
- Laptop Direct Connect 33
- RS232 Serial Port 34
- RS485 Packet Mode 35
- RS485 Packet Length 35
- USB IBM SurePos 36
- USB PC or Macintosh Keyboard 36
- USB HID Bar Code Scanner 37
- USB Serial 37
- CTS/RTS Emulation On 37
- * CTS/RTS Emulation Off 37
- ACK/NAK Mode On 38
- * ACK/NAK Mode Off 38
- Verifone Ruby Settings 38
- Gilbarco Settings 39
- Honeywell Bioptic Settings 39
- NCR Bioptic Settings 40
- Keyboard Country Layout 42
- Keyboard Country (continued) 43
- Program Keyboard Country 49
- * Regular 49
- Caps Lock 49
- Shift Lock 49
- Automatic Caps Lock 49
- Keyboard Conversion 50
- Control Character Output On 51
- Default = Off 52
- * Automatic Direct Connect 53
- Mode Off 53
- RS232 Baud Rate 54
- Default = 8 55
- Default = 1 55
- Default = None 55
- RS232 Receiver Time-Out 56
- Flow Control, No Timeout 56
- * RTS/CTS Off 56
- Two-Direction Flow Control 56
- Flow Control with Timeout 56
- RS232 Timeout 57
- * XON/XOFF Off 57
- XON/XOFF On 57
- ACK/NAK On 58
- * ACK/NAK Off 58
- * Packet Mode Off 58
- Packet Mode On 58
- * Bioptic ACK/NAK Off 59
- Bioptic ACK/NAK On 59
- ACK/NAK Timeout 59
- Cordless System Operation 61
- System Conditions 63
- Page Button 64
- About the Battery 64
- Charging Information 65
- Battery Recommendations 65
- Reset Scanner 68
- Scanning while in Base Cradle 68
- * Paging Mode On 69
- Paging Mode Off 69
- * Low (1000 Hz) 69
- Medium (3250 Hz) 69
- High (4200 Hz) 69
- * Razz (250 Hz) 70
- Scanner Report 70
- Scanner Address 71
- Base Address 71
- Charge Only Mode 71
- * Charge and Link Mode 72
- Locked Link Mode 72
- (Single Scanner) 72
- * Open Link Mode 73
- Unlink Scanner 73
- Override Locked Scanner 73
- Alarm Sound Type 74
- Flexible Power Management 75
- Reset Base 76
- Automatic Batch Mode 77
- * Batch Mode Off 77
- Inventory Batch Mode 77
- * Batch Mode Beep On 77
- Batch Mode Beep Off 77
- RAM Storage 78
- * Flash Storage 78
- Batch Mode Quantity On 78
- * Batch Mode Quantity Off 78
- Quantity Codes 79
- Quantity Codes (continued) 80
- Batch Mode Output Order 80
- Delete Last Code 80
- Clear All Codes 80
- Multiple Scanner Operation 81
- Application Work Groups 84
- All Application Work Groups 85
- Custom Default Settings: 86
- All Work Groups 86
- Non-Base BT Connection 87
- Bluetooth PIN 87
- * Auto Reconnect On 88
- Auto Reconnect Off 88
- Maximum Link Attempts 89
- Relink Time-Out 90
- Host Command Acknowledgment 91
- Host ACK On 92
- * Host ACK Off 92
- Command Action 93
- Input/Output Settings 95
- Trigger Click On 96
- *Trigger Click Off 96
- * Beeper - Good Read On 96
- Beeper - Good Read Off 96
- Beeper Volume – Good Read 97
- Beeper Pitch – Good Read 97
- Beeper Pitch – Error 98
- Beeper Duration – Good Read 98
- LED – Good Read 98
- Number of Beeps – Good Read 99
- Number of Beeps – Error 99
- * No Delay 100
- Short Delay (500 ms) 100
- Medium Delay (1,000 ms) 100
- Long Delay (1,500 ms) 100
- * Manual Trigger - Normal 101
- Manual Trigger - Enhanced 101
- Read Time-Out 101
- Default = 3600 seconds 102
- Presentation Mode 103
- * LEDs On 103
- LEDs Off 103
- Sensitivity 103
- In-Stand Sensor Mode 104
- Streaming Presentation 104
- Hand Held Scanning - Mobile 105
- Streaming Presentation 105
- Mobile Phone 105
- Image Snap and Ship 106
- Hands Free Time-Out 106
- User-Specified Reread Delay 107
- Illumination Lights 107
- Aimer Delay 108
- Scanner Time-Out 108
- * Interlaced 109
- * Preferred Symbology Off 111
- Preferred Symbology On 111
- High Priority Symbology 111
- Low Priority Symbology 112
- Preferred Symbology Time-out 112
- Preferred Symbology Default 112
- Output Sequence Overview 113
- Other Programming Selections 114
- Output Sequence Example 114
- Default Sequence 115
- Enter Sequence 115
- Transmit Partial Sequence 116
- * Discard Partial Sequence 116
- Required 116
- On/Not Required 116
- Default = Off 117
- Video Reverse Only 118
- * Video Reverse Off 118
- VIDREV0 118
- Data Editing 119
- Add CR Suffix 121
- All Symbologies 121
- Add Prefix 121
- Clear One Prefix 121
- Clear All Prefixes 121
- Add Suffix 122
- Clear One Suffix 122
- Clear All Suffixes 122
- * Enable 122
- Intercharacter Delay 123
- Interfunction Delay 124
- Intermessage Delay 124
- * Default Data Format 125
- Enter Data Format 126
- Clear One Data Format 127
- Clear All Data Formats 127
- Data Format Editor Commands 128
- Terminal ID Table 128
- Move Commands 129
- Search Commands 130
- Miscellaneous Commands 131
- Data Formatter Off 132
- Required, Keep Prefix/Suffix 133
- Primary Data Format 134
- Data Format 1 134
- Data Format 2 134
- Data Format 3 134
- Single Scan-Data Format 1 135
- Single Scan-Data Format 2 135
- Single Scan-Data Format 3 135
- Single Scan-Primary 135
- Data Format 135
- Symbologies 137
- All Symbologies On 138
- All Symbologies Off 138
- Transmit 139
- * Don’t Transmit 139
- D5 6 7 8 A 140
- Minimum Message Length 141
- Maximum Message Length 141
- * Don’t Transmit 142
- * No Check Character 143
- Validate and Transmit 143
- Validate, but Don’t Transmit 143
- 32 Pharmaceutical codes 144
- * Full ASCII Off 145
- Full ASCII On 145
- Code 39 Code Page 146
- * No Check Digit 147
- Code 93 Code Page 151
- One Check Digit 154
- * Two Check Digits 154
- Code 128 Code Page 156
- Original Telepen Output 158
- * AIM Telepen Output 158
- Telepen Message Length 159
- UPC-A On/Off 159
- UPC-A Check Digit 159
- UPC-A Number System 160
- UPC-A Addenda 160
- UPC-A Addenda Required 160
- Allow Concatenation 161
- Require Concatenation 161
- * UPC-E0 On 162
- UPC-E0 Off 162
- UPC-E0 Addenda Required 163
- UPC-E0 Addenda Separator 163
- UPC-E0 Check Digit 163
- UPC-E0 Number System 164
- UPC-E0 Addenda 164
- EAN/JAN-13 165
- EAN/JAN-13 Addenda 166
- EAN/JAN-13 Addenda Required 166
- EAN/JAN-13 Addenda Separator 167
- ISBN Translate 167
- EAN/JAN-8 168
- EAN/JAN-8 Addenda 169
- EAN/JAN-8 Addenda Required 169
- EAN/JAN-8 Addenda Separator 169
- MSI On/Off 170
- MSI Check Character 170
- MSI Message Length 171
- GS1 DataBar Omnidirectional 172
- GS1 DataBar Limited 172
- Trioptic Code 174
- Codablock A 174
- Maximum Message Length 177
- Minimum Message Length 177
- GS1 Composite Codes 179
- GS1 DataBar Emulation 180
- GS1-128 Emulation 180
- * GS1 Emulation Off 180
- GS1 Code Expansion Off 180
- EAN8 to EAN13 Conversion 180
- TCIF Linked Code 39 (TLC39) 181
- Postal Codes - 2D 187
- Combination 2D Postal Codes: 188
- * Don’t Transmit Check Digit 190
- Transmit Check Digit 190
- Korea Post 192
- Imaging Commands 193
- Image Snap - IMGSNP 194
- (Default = 7874) 195
- (default) 195
- Image Ship - IMGSHP 197
- (default) 204
- (default) 204
- Force VGA Resolution 206
- * Native Resolution 206
- Optimize On 206
- * Optimize Off 206
- IMGBOX Modifiers 207
- Example: IMGBOX245w37h55y 209
- RF Default Imaging Device 211
- Interface Keys 213
- Supported Interface Keys 215
- Add Code I.D. Prefix to 221
- All Symbologies (Temporary) 221
- Show Decoder Revision 221
- Show Scan Driver Revision 221
- Show Revision 221
- Data Format Settings 222
- Application Plug-Ins (Apps) 223
- EZConfig Introduction 223
- EZConfig Operations 224
- Serial Programming Commands 227
- Query Commands 228
- Examples of Query Commands 229
- Activate Custom Defaults 230
- * Indicates default 231
- # Indicates a numeric 231
- Product Specifications 267
- Parameter Specification 268
- CCB01-010BT Charge Base 269
- 10 Pin RJ41 Modular Plug 270
- 10 Pin Modular Plug 273
- Maintenance 275
- Replacing an Interface Cable 276
- Troubleshooting a 277
- Xenon Scanner 277
- Troubleshooting a Base 278
- Customer Support 281
- Online Technical Assistance 282
- Limited Warranty 283
- Reference Charts 285
- Sample Symbols 293
- Car Registration 294
- Zip Code 294
- Test Symb ol 294
- Package Label 295
- Test Message 295
- Programming Chart 296
- 9680 Old Bailes Road 298
- Fort Mill, SC 29707 298
- Xenon-UG Rev B 298
Related products and manuals for Bar code readers Honeywell Scanner 1900
Bar code readers Honeywell 3800gHD User Manual
(156 pages)
(156 pages)
Bar code readers Honeywell 4820 User's Guide
(284 pages)
(284 pages)
(188 pages)© 2020, manymanuals.com. All rights reserved. | 0.197 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals