Honeywell SC1000 User Manual Page 121
- Page / 174
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
SC Series Instruction Manual page 121
High-Level Input Channel12
12.7 Analog Output Configuration
12.7.1 Identifying the
Output Type
A High-Level Input channel is available with one of two types of digital-to-analog
(DAC) outputs: voltage or current. You can determine which type of output a
channel has by one of three ways:
• Consulting the instrument’s Customer Information Sheet
• Examining the
SYSTEM MENU
->
CONFIGURATION
->
CHANNEL
nn
TYPE
menu item where
nn is the number of the channel. If the channel’s type is
HIGH-LEVEL V
, it has a
voltage output. If the channel’s type is
HIGH-LEVEL I
, it has a current output.
• Examining the channel’s circuit board as shown in the figure below.
12.7.2 Channel Menu Items
The Analog Output can be driven by any channel’s track, peak or valley value.
See the “Channel Menu” section earlier in this chapter for a complete listing of
SETUP menu items available on the
DAC. SETUP
sub-menu.
12.7.3 Output Selection
Jumpers located on the channel’s circuit board determine what outputs are gener-
ated when the value selected to drive the Analog Output (from the
DAC. CHANNEL
and
DAC. SOURCE
menu items) equals the
DAC. FULL SCALE
and
DAC. ZERO SCALE
settings.
Figure 12-9: Digital-to-Analog Output Jumper Locations
DAC. ZERO SCALE
Output
DAC. FULL SCALE
Output
J30
jumper
J31
jumper
CHANNELS WITH VOLTAGE OUPUT
0-5V 2.5 Volts 5 Volts open closed
±5V 0 Volts 5 Volts open open
0-10V 5 Volts 10 Volts closed closed
±10V 0 Volts 10 Volts closed open
CHANNELS WITH CURRENT OUTPUT
4-20mA 4 mA 20 mA open open
4-20mA 12 mA 20 mA open closed
- SC Instrumentation 1
- Contents 3
- Chapter 1 9
- Introduction 9
- 1.2 Related Documents 11
- 1.3 What is the SC Series? 12
- Signature Calibration 14
- Chapter 2 15
- Getting Started Quickly 15
- 2.3 Turn on the Instrument 16
- page 18 008-0608-00 18
- Chapter 3 19
- Operating Modes 19
- 3.3 RUN Mode 20
- 3.3.4 [CHANNEL] button 21
- 3.3.5 [TARE] button 21
- 3.3.6 Indicator Lights 21
- 3.4 ERROR mode 22
- 3.5 SETUP Menu mode 23
- page 24 008-0608-00 24
- Chapter 4 25
- Chassis Models 25
- 4.2 Specifications 26
- 4.3 Models SC1000 and SC2000 27
- 4.3.5 Rack Mounting 28
- 4.3.6 Bench Mounting 28
- 4.3.7 Case Removal 28
- 4.3.8 Internal Arrangement 29
- 4.4 Model SC2001 31
- 4.4.5 Internal Arrangement 32
- 4.4.6 Cleaning 32
- 4.4.7 Vehicle Power Option 32
- 4.4.8 Fuse Replacement 32
- 4.5 Model SC3004 33
- Chapter 5 35
- System Connector 35
- 5.2 System Connector Pinout 36
- 5.3 Function Input Pins 37
- 5.4 Limit Output Pins 38
- System Connector5 39
- page 40 008-0608-00 40
- Chapter 6 41
- System Menu 41
- ARE YOU SURE 44
- ARE YOU SURE? 44
- System Menu6 45
- page 46 008-0608-00 46
- Chapter 7 47
- Serial Communications 47
- 7.3 Communications Protocol 48
- 7.4 Serial Com Menu 49
- page 50 008-0608-00 50
- Chapter 8 51
- Display Menu 51
- page 52 008-0608-00 52
- Chapter 9 53
- 9.2 Limit Operation 54
- 9.3 Limit Menus 55
- page 58 008-0608-00 58
- Chapter 10 59
- Strain-Gage Input Channel 59
- 10.2 Wiring 60
- 10.3 Calibration Procedure 61
- 10.4 Specifications 62
- 10.5 Channel Menu 63
- 10.6.1 Identifying the 76
- 10.6.2 Channel Menu Items 76
- 10.6.3 Output Selection 76
- 10.7 Troubleshooting 77
- Chapter 11 79
- AC/AC-LVDT Input Channel 79
- 11.2 Wiring 80
- 11.3 Calibration Procedure 81
- 11.4 Specifications 82
- 11.5 Channel Menu 83
- HIGH/LOW HOLD 86
- HIGH/LOW CLEAR 86
- TARE OFF 86
- 11.6.1 Overview 93
- 11.6.2 Procedure 93
- 11.7.1 Identifying the 94
- 11.7.2 Channel Menu 94
- 11.7.3 Output Selection 94
- 11.8 Troubleshooting 95
- page 96 008-0608-00 96
- Chapter 12 97
- High-Level Input Channel 97
- 12.2 Wiring 98
- 12.2.2 Bi-polar Voltage 99
- 12.2.3 “3-wire 100
- Voltage” Amplifiers 100
- 12.2.4 “3-wire Voltage” 101
- Amplifiers with Single-wire 101
- Shunt Cal 101
- 12.2.5 “3-wire Current” 102
- Amplifiers 102
- Amplifiers with Buffered 103
- 12.2.6 “2-wire Current” 103
- 12.2.7 “2-wire Current” 104
- Amplifiers with Single 104
- 12.2.8 Low Voltage DC-DC 105
- 12.3.1 Overview 106
- 12.3.2 Setting Jumpers 106
- 12.4 Calibration Procedure 107
- 12.5 Specifications 108
- 12.6 Channel Menu 109
- TRACK / PEAK 110
- TRACK / VALLEY 110
- PEAK / VALLEY 110
- Sub-Menu 111
- Menu Items 112
- Menu Item 113
- Sub-Menu 119
- 12.7.1 Identifying the 121
- Output Type 121
- 12.7.2 Channel Menu Items 121
- 12.7.3 Output Selection 121
- 12.8 Troubleshooting 122
- Chapter 13 123
- Relay Output Channel 123
- 13.2 Wiring 124
- 13.3 Setup Procedure 125
- 13.4 Specifications 126
- 13.5 Channel Menu 127
- page 128 008-0608-00 128
- Chapter 14 129
- DAC Output Channel 129
- 14.2 Wiring 130
- 14.3 Setup Procedure 131
- 14.4 Specifications 132
- 14.5 Channel Menu 133
- 14.6.1 Identifying the 135
- 14.6.2 Channel Menu Items 135
- 14.6.3 Output Selection 135
- 14.7 Troubleshooting 136
- DAC Output Channel14 137
- page 138 008-0608-00 138
- Chapter 15 139
- Split Display Virtual Channel 139
- 15.4 Channel Menu 140
- 15.5 Troubleshooting 140
- page 142 008-0608-00 142
- Chapter 16 143
- Mathematics Virtual Channel 143
- 16.2 Wiring 144
- 16.3 Setup Procedure 145
- 16.4 Channel Menu 146
- 16.5 Troubleshooting 149
- page 150 008-0608-00 150
- Chapter 17 151
- Error Messages 151
- 17.2 Error Message List 152
- UNREACHABLE GOTO 156
- GOTO NOT JUMP 156
- Chapter 18 157
- Setup Menu Reference 157
- Warranty 173
Related products and manuals for Sensors Honeywell SC1000
Sensors Honeywell CTP-20 User Manual
(4 pages)
(4 pages)
Sensors Honeywell C7189U User Manual
(12 pages)
(12 pages)
Sensors Honeywell 69-2043EFS User Manual
(4 pages)
(4 pages)
Sensors Honeywell C7189A User Manual
(4 pages)
(4 pages)
Sensors Honeywell T7047C User Manual
(8 pages)
(8 pages)
Sensors Honeywell C7089 User Manual
(12 pages)
(12 pages)
© 2020, manymanuals.com. All rights reserved. | 0.287 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals