Honeywell VISIONPRO TH8320 User Manual download pdf (Page 16)

VisionPRO

8000 Touchscreen Programmable Thermostat

68-0280—01 16

Table 3. Installer Setup Menu.

Installer Setup

Number Installer Setup Name Settings Notes

0120 Date (Year Upper) Select first two digits of current calendar year (2005, etc) 2001 - 2178 available

0130 Date (Year Lower) Select last two digits of current calendar year (05 for year

2005, etc)

2001 - 2178 available

0140 Date (Month) Select number that represents current calendar month —

0150 Date (Day) Select number that represents current calendar date —

0160 Schedule Options 0—nonprogrammable

4—7-day programmable

—

0170 System Type Selection 1—1 heat/1 cool conventional (factory setting)

2—single-stage heat pump (no auxiliary heat)

3—heat only conventional (no fan) Also for 750mV.

4—heat only conventional (with fan)

5—heat only (power to open and power to close zone

valves or normally-open zone valves)

6—cool only conventional

7—2 heat/1 cool heat pump (with auxiliary heat)

8—2 heat/2 cool multistage conventional

9—2 heat/1 cool multistage conventional

10—1 heat/2 cool multistage conventional

11—2 heat/2cool heat pump (no auxiliary heat)

12—3 heat/2cool heat pump (with auxiliary heat)

Available options and

defaults vary by

thermostat. System

selection automatically

modifies some default

settings and/or hides

other Installer Setup

options.

0180 Fan Control in Heating 0—gas or oil furnace equipment controls fan in heating

(factory setting)

1—electric furnace—thermostat controls fan in heating

Only shown if

conventional system is

selected. If heat pump is

chosen, fan defaults to

electric.

0190 Changeover Valve—O/B

Terminal Energized in

Heating or Cooling

(Heat Pumps Only)

0—changeover valve—O/B terminal is energized in

cooling (factory setting)

1—changeover valve—O/B terminal is energized in

heating

Only shown if heat pump

system is chosen.

0200 Backup Heat Source

(Auxiliary Heat)

0—heat pump backup heat source is electric (factory

setting)

1—heat pump backup heat source is fossil fuel

Only shown if 2 heat/

1 cool or 3 heat/2 cool

heat pump is chosen

0210 External Fuel Fossil

Fuel Kit

0—no external fossil fuel kit is controlling heat pump

backup heat. This thermostat controls the dual fuel. Must

install outdoor sensor and set Installer Setup Number

0340 to number 2.

1—external fossil fuel kit is controlling heat pump backup

heat

Only shown if fossil fuel is

chosen as backup heat

source.

0220 Cycles per hour (cph) for

1st Stage Compressor

3—cph recommended for compressors (factory setting)

1, 2, 4, 5, 6—

other cycle rate settings

—

0230 Cycles per hour (cph) for

2nd Stage Compressor

3—cph recommended for compressors (factory setting)

1, 2, 4, 5, 6—other cycle rate settings

Only shown if two stages

of cool are selected.

0240 Cycles per hour (cph) for

1st Stage Conventional

Heat

1— 1 cph used for steam and gravity

3—3 cph used for hot water system and high efficiency

(90% or better) furnaces

5—5 cph used for standard fossil fuel forced air (less than

80% efficient) systems (factory setting)

9—9 cph used for electric furnaces

2, 4, 6, 7, 8, 10, 11, 12—other cycle rate settings

Not shown if system

selection is heat pump.

Selection in this stage

changes default cph for

2nd stage heat.

0250 Cycles per hour (cph) for

2nd Stage Heat (Aux

Heat for 2H/1C Heat

Pumps)

1—1 cph used for steam and gravity

3—3 cph for hot water systems and high efficiency (90%

or better) furnaces

5—5 cph for standard fossil fuel forced air (less than 90%

efficient) systems (factory setting)

9—9 cph used for electric furnaces or electric auxiliary

heat for heat pump systems

2, 4, 6, 7, 8, 10, 11, 12—other cycle rate settings

Only shown if two stages

of heat are selected.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 39 40

Comments to this Manuals

No comments

Honeywell VISIONPRO TH8320 User Manual Page 16

Comments to this Manuals

Related products and manuals for Thermostats Honeywell VISIONPRO TH8320